TAC Xenta^TM #101-2VF-A LonMark^TM Fan-Coil controller with new optional configuration for Under Floor HVAC Modules.

TAC has released the #101-2VF-A LonMark approved Zone Controller. The #101-2VF-A controller meets the LonMark open protocol profile Fan-Coil controller plus new optional configuration for Under Floor HVAC modules. The controller can be used on a LonWorks TP-FT10 open protocol network or operate as a "stand alone" controller. The #101-2VF-A compliments the present line-up of Zone Controllers for VAV box's, Fan-Coil units and HVAC Roof Top Units & Single Zone equipment. The TAC Xenta #101-2VF-A controller can be connected by way of the LonWorks network directly to TAC Vista Central System front end to make a complete Building Automation package.

For more information contact Steve Karsten 

Armstrong Presents New Electronic Steam Humidifier With Ionic Bed Technology

THREE RIVERS, MI: April 13, 2000  Indoor air quality, specifically proper humidification levels, is essential for personal comfort, safety, and for the protection of sensitive electronic equipment that can be damaged with a single electrostatic discharge. To meet the growing need for quality steam humidification, Armstrong International, Inc. presents its Series HC-4000 HumidiClean™ electronic steam humidifier with patented ionic bed technology. 

The HumidiClean™ humidifier includes five disposable inserts, each containing a fibrous media referred to as an ionic bed. These ionic beds attract solids from the boiling water, preventing the solids from plating out on the heating elements or on the inner stainless steel tank walls. Therefore, tank cleaning is minimized and the effective service life of parts, especially the submersed elements which traditionally accumulate scale and chemical deposits, is greatly extended. Thus, the tank compartment stays cleaner longer, and the unit maintains its high solids gathering efficiency and maximum capacity throughout its operating cycle.

The submersed heating elements generate quality steam regardless of water quality or its conductivity and the unit provides the full-range of modulation. Tap water, without the addition of additives or harsh chemicals, can be used to produce clean, effective steam humidification. Deionized, demineralized, softened or reverse osmosis water sources, also may be used. 

For additional information visit the web site at http://www.armstrong-intl.com/products/humidifiers/hclean.php3

Allen-Bradley IntelliCENTER™ Motor Control Center (MCC) Delivers Intelligent, Integrated Diagnostic and Monitoring Solutions 

World-class design offers users unprecedented hardware, software and communication integration

MILWAUKEE, April 10, 2000 – Complete automation leader Rockwell Automation introduced today the Allen-Bradley IntelliCENTER™ motor control center (MCC), providing MCC users unprecedented hardware, software and communication integration. Leveraging the Allen-Bradley CENTERLINE® MCC design, the most popular MCC in North America, the IntelliCENTER features dynamically configured screens that show real-time data, trending, component history, wiring diagrams, user manuals and spare parts. The IntelliCENTER reduces installation time with its plug-and-play setup and minimizes facility downtime by quickly providing intelligent diagnostic and predictive failure information.

For more information go to www.rockwellautomation.com.

New Communication Module from Rockwell Automation Features Four (4) Input Points

MILWAUKEE, April 10, 2000 — Complete automation leader Rockwell Automation has introduced the Allen-Bradley Bulletin 2100-GK61 module for DeviceNet™ communications. The new module provides a flexible communication interface between the DeviceNet network and any SCANport™ product, including Allen-Bradley Bulletin 1305, 1336 PLUS and 1336 PLUS II AC drives, Allen-Bradley SMC Dialog Plus™ motor controllers and SMP-3™ overload relays. Ideal for integrating communication within motor control centers, the module features four digital inputs for monitoring disconnect auxiliary contacts, Hand-Off-Auto switches and motor starter contacts via DeviceNet to increase diagnostic and monitoring capabilities.

For more information go to www.rockwellautomation.com

New OptiView™ Chiller Graphic Control Center Delivers Optimum Control for Optimum Performance

YORK, Pa.- The new OptiView™ Graphic Control Center from York International Corporation gives operators a detailed look at how well their chiller is working. Better access to operating data enables real-time "tuning," so chillers can operate at peak efficiency, even at off-design conditions. Armed with real-time data, operators can adjust the chiller to optimize performance, simplify maintenance scheduling and improve reliability by pinpointing problems before they cause downtime. 

The YORK OptiView uses the same AMD processor and flat-panel LCD screen found on many laptop computers to deliver the industry's only graphical interface to a chiller control. Unlike two- or three-line text-only displays, the OptiView displays chiller operation details with more than 30 full-screen, full-color diagrams, charts, and input illustrations. 

The new OptiView™ Graphic Control Center is available on YORK centrifugal and screw chillers.

For more information visit www.york.com/optivew.

TAC has received the approval to ship the TAC Xenta #301, #302, & #401 version 3.3 programmable DDC controllers with a LonMark certification as a "Plant Controller".

The #300 and #401 controllers meet the "Plant Controller" requirements for a LonMark certification stamp.

The #300 and #401 controllers meet the LonMark open protocol profile using the approved input and output SNVT variables for standard interface and management of LonMark zone controllers or other LonMark certified devices. The controller's can also be used on a LonWorks TP-FT10 open protocol network or operate as a "stand alone" controller. The controllers can be used for plant management operations, data logging, DDC and EMS operations, and alarm handling. The controllers also contain a customized menu for the hand held Operators Panel for building wide human interface at the local level. The controller's can be connected by way of the LonWorks network directly to TAC Vista Central System front end to make a complete Building Automation package with color graphics, alarm handling, data log's executive reports, CMM functions, IP integration to the WEB.

For more information contact Steve Karsten 

Delta Controls DAC 25x 

Surrey, BC, Canada Delta Controls Inc. is proud to announce the release of its newest Delta Application Controller (DAC) - the DAC 25x^TM. The DAC 25x is a fully programmable DDC controller for operating various types of terminal unit and unitary HVAC equipment as a stand-alone device or part of a fully integrated building automation system.

The DAC 25x contains a number of advanced features:

• Comprehensive LCD and programmable keypad interface
• Fully programmable for multiple control applications and zone / room control
• EIA-485 and EIA-232 networking and system accessibility
• Availability as Native BACnet^TM or proprietary Intelli-Sys^TM.

Contact Delta Controls for more information.

Last Month's New Products

[an error occurred while processing this directive]
[Click Banner To Learn More]

[Stay Informed - Subscribe to our Update Mailing List]
[Home Page] [Contact Us] [The Automator - Current Issue]
[News] [Systems] [Products] [Resources] [About]

Visit Home Toys to Learn about Home Automation

Web Design by HomeToys
©Enviromation 1999